It is cement based, polymer modified, super elastic, two component waterproofing and concrete protection mortar. The liquid component is pure elastomeric resin emulsion. The powder component is hydraulic connective that is a composition of additive and filling materials.
Description
It is a double-component, cement-based, acrylic modified, elastic waterproof coating mortar whose liquid component is a pure elastomeric resin emulsion, and powder component is a mixture of hydraulic binder, additive and filler.
Usage Areas
• It is used on surfaces like concrete, screed and plaster.
• It is used in exterior and interior applications.
• It is used in horizontal and vertical applications.
• It is used for the positive (inside) insulation of water tanks,pools, and cisterns made up of bricks or, rough or plastered cement.
• In waterproofing of terrace roofs, it is used as a base coat under the coating or as the top coat.
• It is used for the positive insulation of foundations, retaining and shear walls against ground humidity and water leakage.
• It is used for waterproofing basements from outside.
• It is used for waterproofing planter boxes from inside.
• It is used for waterproofing the floor of damp environments such as bathrooms, kitchens, toilets, etc. to prevent water leakage to the storey below.
• It is used for coating sea water and waste water drainage channels and chambers. (with special formula)
• It is used for waterproofing galleries, and drainage and water channels.
• In bridges, viaducts, and engineering works it is used as aprotective coating against defrosting salts.
• It is used for adhering coating materials such as ceramic, granite, marble, etc.
Advantages
• It can be applied on vertical and horizontal places with roller, brush or spray gun.
• It makes a seamless coating.
• It can applied onto damp surfaces.
• It is practical to use. You just mix the powder component with the liquid component and apply.
• It provides an economical solution.
• It is applied onto the side exposed to water (positive water pressure).
• It is elastic.
• It protects concrete and plaster surfaces against air pollution, and acidic atmospheric gases.
• It is suitable to contact with potable water.
(ODTÜ Report No.: 2014.03.04.147/ Report Date: 24.03.2014)
• While it is waterproof, it provides breathability for the surface.
• It protects concrete and plastered surfaces from carbonization and chloride.
Application
• 10 kg of liquid component of Permo-Chim Duo is poured into a clean container and powder component is added; it is mixed to a thick, homogenous consistency. Permo-Chim Duo is applied at least in two coats with a brush, roller, or trowel.
• Each coat must be applied as the former coat starts to solidify, and before it dries up.
• If necessary, the floor must be slightly moisturized before the application of the second coat.
• Cracks and vertical/horizontal seams must be reinforced with materials such as seam tape, plaster mesh, etc. between the application of two coats.
• Application onto perlite concrete, gas concrete or any high porosity concrete requires extra attention; Permo-Chim Duo must be applied onto these surfaces after the application of alum or plaster.
• After coating the surfaces like terraces, application area must be opened the food traffic after the applications of ceramic or tiles.
• Mechanical strenght gained after 3 days, waterproofing abilitystarts after 7 days. Final curing in 14 days.
• Must be protected from punch and impact before covering the surface.
• Product must be consumped in 30 minutes after mixing two components.
Consumption
Depending on surface conditions, minimum two coats must be applied. For each coat 1 -1,5 kg/m2. High pressure areas like water tanks and pools, application must be applied on 3 coats and reinforced with fiber mesh.
Packaging
20 kg Kraft Bag + 10 kg Plastic Drum = 30 kg Set 20 Sets / Pallet
PROPERTY |
RESULT |
CHEMICAL STRUCTURE |
COMPONENT A: Mineral filler, polymer modified admixtures and special cement |
COMPONENT B: Copolymer Acrylic Dispersion |
|
COLOR |
Greenish grey |
DENSITY |
1,70 kg/lt |
ADHESION STRENGTH |
>1,00 N/mm2 |
RESISTANCE TO PRESSURIZED WATER (DIN 1048) |
7 bars (positive) |
CAPILLARY WATER ABSORPTION (TS EN 12808-5) |
<0,10 gr (after 4 hours) |
APPLICATION GROUND TEMPERATURE |
(+50C) – (+250C) |
SERVICE TEMPERATURE |
(-200C) – (+800C) |
MATURITY PERIOD |
3 – 5 minutes |
USAGE PERIOD |
2 hours |
PERIOD TO WAIT BEFORE OPENING TO SERVICE / MECHANIC STRENGTH |
2 days / 7 days |
PERIOD TO WAIT BEFORE COATING ITS TOP BY PLASTE/ BY CERAMIC |
3 days / 3 days |